건전하고 투명한 장터/커뮤니티 형성과 활성화를 위해
휴대폰 본인인증한 회원만 글쓰기(댓글쓰기)가 가능합니다.
회원님 명의의 휴대폰번호로 인증하게 되며 이용료는 무료입니다.
위와 같은 운영에 회원님들의 협조와 양해 부탁드립니다. 감사합니다.
TEL : 재고문의는 꼭 카톡으로주세요. 02-2636-8274
FAX : 02-2636-8264
E-MAIL : service@drumall.com
주변에 튜닝 고수님들이 계시면 직접 찾아가서 한 수 배우시는게 가장 좋을 듯 합니다.
글고 튜닝은 하루 아침에 뚝딱 되는 것이 아니라 스네어와 엄청 씨름을 해야 겨우 감이 올까
말까 그 정도.....-_- 입니다..ㅋㅋㅋㅋㅋ 그리고 본인이 듣기에 와우! 좋은 소리여도
청중이 들었을 때는 꽝인 경우가 허다하니 10m정도 떨어져서도 한 번 테스트를 하는 것이
현명하겠죠??^^;;; (하수 초보의 그냥 지나쳐도 되는 글 입니다 ㅋㅋ)
원하시는 소리가 어느 소리인지 먼저 아셔야 할것 같고
많은 분들이 탑헤드로 코티드 엠퍼러 보다는 엠버서더를 선호한다는 점에서 앙코르 모델이라도 구해서 한번 테스트를 해보시는것도 추천드리구요
제가 마펙스 Horizon이라는 모델에 대한 정보가 전혀 없어서 그런데
어느정도 급인지는 모르겠으나 스네어 자체 성격이 영맨님이 원하는 소리와 다른 경우도 있을수 있겠습니다.
그리고 와이어도 마찬가지인데요 저도 울트라 사운드가 참 저랑 안맞거든요..
울트라 사운드 제품을 선호하시는 분들께 악의는 없고 죄송한 말씀이지만 저한테는 잘 안맞아서;;
영맨님도 저랑 비슷한 경우가 아니지 않을까 생각이 됩니다.
저는 보통 고가쪽 스네어에 깔끔한 빡! 떡! 소리를 원할때는 그냥 평범하게 엠버서더 코티드 끼워서 요리조리 만져보고 쓰고요 좀더 알맹이진 소리를 원하면 CS 닷헤드를 사용합니다.
그리고 보통 보급형 드럼 번들 스네어에는 CS 클리어 화이트닷 헤드를 사용합니다.
팡팡 ~ 아주 시원한 소리가 드럼 전체 분위기 자체를 바꿔버려요 ^^
위아래 헤드의 음정 차이를 줄여보세여. 헤드음정 찾으시고 바텀을 일단 헤드와 세임튠하시고 아주 조금씩 하피튠을바꿔보시되 잡음 나기전까지만 음정차를 두세여. 살짝나는건 상관없구여~^^
타점이 중앙에서 조금만 벗어나도 소리가 이상하게 나는건 튜닝이 잘못 된 게 맞습니다. 각 텐션마다 동일하게 조여지지 않은 증거 중 하나입니다. 근데 탑헤드가 좀 두꺼운 걸 쓰는 게 아닌가 하는 생각이 듭니다. ㅎㅎ 보통 엠버서더 코티드를 상피로 많이 쓰구요. 어떤 스네어든 엠버서더로 튜닝법을 연구 및 공부하는게 좋다고 생각합니다. 물론 개인적인 생각이라 무시하셔도 됩니다.
하피를 쉘 음정에 맞추고 상피를 좀 더 조인다던지 하는 튜닝도 좋지만 가장 좋은 튜닝은 어떤 음정을 잡던 상관없이 모든 텐션을 최대한 동일하게 조여주는게 튜닝입니다. 하지만 동일하게 조여주는 방법이 사람마다 다르기 때문에 노하우도 다르고 톤도 다르게 나오고 게다가 사람마다 터치가 달라서 완전 다른 소리로 바뀌지만 튜닝만 놓고 말씀드리면 동일하게 조일 경우 사람마다 다르지만 막상 도달하면 비슷합니다. 연주해보면 알아요. 요놈이 제대로 튜닝 된거구나 안된거구나 말이죠.
각 텐션을 동일하게 조이는 방법은 주위에 절대음감을 지닌 사람을 데려와서 물어보세요. 저도 그렇게 시작했습니다. ㅎㅎ 그 사람 데려다가 맛있는거 사준다 약속하시고, 여기랑 여기랑 음높이가 어떠냐 물어보세요. 그러면서 본인도 들으세요. 그럼 대충 감이 오고 타악기 음색이 귀에 익습니다. 또 하나는 급할 때 쓰는 방법인데 텐션에서 2센티정도 떨어진 부분을 엄지손가락으로 눌러보세요. 각 텐션마다 동일하게 조여졌는지 아닌지 확인할 수 있습니다. 조여진 부분을 풀어주고 헐렁한 부분을 조금 조여주면 얼추 톤이 나와요.
자세한건 튜닝 잘하시는 분 불러서 직접 눈으로 보고 귀로 익히는 수 밖에 없어요~ 사람마다 차이가 있겠지만 혼자서는 너무 오래 걸립니다... 저도 기본적인 튜닝 방법과 나만의 톤을 찾기 위해 한 3,4년 고생했습니다 ㅎㅎ;
그럼 튜닝 잘하시길...^^
-
헤드를 적절히 사용하셨다고 가정해 볼게요. (보통 얇은거.), 바텀은 가장 얇은 거
클리어는 좀 오버톤이 많은, 보다 밝은 소리를 내주고요, 코티드는 약간 컨트롤된 따뜻한 소리를 내줍니다.
(전체적으로는, 코티드를 훨씬 많이 씁니다.)
-
1. 일단 바텀을 꽉 조여서 헤드를 펴주세요.
2. 조금씩 풀어가며 통음정에 맞추세요.
3. 풀수록 통의 서스테인이 길어지고 조일수록 소리도 조여집니다 (울림이 짧아짐)
4. 탑헤드도 꽉 조여서 헤드를 펴준 다음에 풀렀다가 다시 잡아주세요.
5. 랙탐과 베이스드럼 스네어는 절대 균일하게 조정, 플로어탐은 마음에 드는 소리가 날 때까지만 풀어주세요.
튜닝은 기본적으로 좀 타이트하게 잡아주는 편이 소리가 멀리 깨끗하게 나갑니다.
혹시나 부연 설명하자면.. 대부분의 스네어쉘은 스네피가 바텀에 딱 붙게 하기 위해서
스네피가 가로지르는 쉘 쪽을 오목하게 파 놓습니다. 이게 스네어 베드구요.
이렇게 해 놓으면 하피를 조일시 하피의 표면이 조금 볼록하게 됩니다.
이 볼록해진 면을 따라 스네피가 딱 붙으면서 스네피가 잘 울고 버징도 없어지게 됩니다.
따라서 파는 방법과 깊이가 스네어의 특징을 지을 만큼 아주 중요합니다.
그런데 이 베드 깊이가 어느 정도 되면 크게 신경 쓰지 않아도 되나 얕은 경우 (예로 프플 같은 경우도 베드가 있습니다. 하지만 매우 얕습니다.)
일반적인 텐션을 일정하게 해주는 튜닝을 하게 되면 버징이 일거나 매우 거슬리는 소리가 납니다.
이때는 대략적인 튜닝을 하시면서 스네어 베드 쪽을 좀더 로우하게 또는 베드와 직각되는 부분의 텐션을 좀더 타이트 하게 조여주시면
바텀이 더 볼록하게 되면서 스네피가 좀 더 밀착하게 됩니다.
베드쪽과 다른 쪽의 텐션 차이를 조금씩 변화를 줘 보시면 확실히 느끼 실 수 있습니다.
스네어 와이어를 바꿔 껴도 사실 별 차이는 없습니다. 차라리 위와 같이 조절하시는 것이
더욱 효과적입니다.
튜닝하시는데 도움 되셨으면 합니다.
펄 포럼을 살펴보다가 왕 프로페셔널한 분께서 포스팅해놓으신 스레드가 너무! 좋아 아래 첨부합니다.
Some tips....
Use drum keys that have some weight to them. It makes them have a much better feel in your hand and make sure you use two of the same model keys so the feeling is the same.
Tension rod "health" is important. If all your tension rods do not feel identical on each drum your tuning, your going to have lots of issues. If they have any visible rust, toss them and replace them. If the rods are fine but there is rust in the Lugs, replace the inserts. And when you put new ones in, LIGHTLY lubricate them with machine oil. LIGHTLY. If oil is dripping off them, you used too much. Aside from making a mess, your going to have lots of detuning issues. The oil is there first and foremost to prevent rust, not so much to lubricate the rods. That is why Pearl is the ONLY drum company smart enough to use stainless steel rods with brass inserts. Brilliant. You have two completley rustproof components and the brass being a softer metal will never let the rods get hung up. That to me is one of the best features of Pearl drums. And all tension rods should have metal washers under the head, then plastic washers touching the hoop. It's very important that all the rods and washers are identical. If you lose one and have to buy a replacement but cannot get the same type, buy enough to do the whole drum. Mismatched wahsers will screw up your tuning feel.
Wipe your edges with a cloth to remove any residue of who knows what. And make sure there is no dust and dirt in the shell. You would be amazed at what the smallest amount of lint will do bouncing on a reso head. All sorts of weird buzzing.
Whenever possible, have the heads your going to be putting on your kit out of the bags and in the same vicinity as the kit for a few hours to acclimate to the room temp. And when you do the head changes and tuning, do it in the same location as the kit. If you come back from the store in the middle of summer with your drumheads in your ice cold A/C car and then go into you hot garage to a head change your going to have issues.
Have a pair of dedicated "drum tuning gloves". Something made of cotton (so they wont scratch). I love regular brown jersey gloves. The reason you want them to be dedicated is there is no chance of them getting any grease, oil or chemicals on them or picking up any dirt that may scratch the shells. You just want to cut the thumb and index finger tips off so you can feel the tension rods with your fingers when tightening. It also means the grease and oil from the tension rods will only be on your skin and not soaking into the gloves. Thaks to the gloves, no fingerprints to wipe off the shells, hardware or head. Why make work for yourself? As long as i have been a tech, my simply way of approcahing my job was Work smarter, not harder. I made everything a science. And i was ALWAYS thinking of new ways to do things better and easier. Halfway through the first year with Skynyrd i found ways to make things so efficient that i could have the kit out of cases, complete head change, tuned, cleaned, ready to play in 35 minutes. And i often tried to beat my record each day. As for tear down after the show? Ask Demfer, he saw. I can have th entire kit off the riser and entireley in cases in 10 minutes flat. All told, i was working 45 minutes a day on normal setup/teardown. That left me LOTS of time to relax and to do routine maintenence or whatever i wanted. It's alot more difficult to tune for someone rather then yourself. Since what may sound great to you is not to them.
Don't fear Lug Locks. They are a great tool if you have de-tuning issues. Especially on snares. In fact, they are the only practical option on the rimshot side where the tension rods keep backing off.
If personally avoid changing batter heads at the same time i am changing reso heads since now your starting from scratch as far as being able to hear when your close in pictch to what the last head was. But it may be unavoidable when your starting out with a new kit. With that in mind, you simply do the same procedure as mentioned above to seat a batter head except have the tom (minus the batter side head and hoop) resting on a clean, soft piece of carpet to protect the edge. When you start the tuning obviously your not going to have a real baseline to work with since there is no head on the oppisite side. So you have to do it mostly by feel. Also, instead of using a drum stick to check the tuning, i use felt cymbal mallets so they don't mark up the head. One you get the reso head close enough, proceed to the batter head installation. Although it's going to be a bit more tricky since your more then likey going to have to make adjustments on both sides to get it right. That is why as i said, i avoid changing both at the same time unless absolutley nessecary. Even if you bought all new heads, top and bottom, with the old batters in place, do the new reso's. Then do the batters, Hopefully you will be close.
NEVER, EVER TRY AND CRACK SNARE SIDE HAZY HEADS WITH YOUR HAND!! You will not be able to do it properly without trashing the head so don't try it!. The only way to do it slightly is with tuning it up high during the initial tuning. I cant tell you how many people tried to return from attempting this.
Gaff Tape, Moon Gel and Reso Rings are not the enemy. They are excellent tools when you need a certain sound but don't feel like swapping out heads with plenty of life left or when your working in the studio and want to have different sounds for different tracks. In fact, it's almost a guarantee in studios. It is not practical to change heads between songs in studios. Gaffer Tape works beautifully. I do agree that it should not be something you use all the time with every head change. If you do, that means you are not choosing the right heads or just do not know how to tune save for a few rare exceptions. Those being the sound you want is even more dead then any head in the brand you endorse offers and to achieve it via tuning would make the head response lousy or some super picky guys who want a sound "just right" where heads and tuning alone just dont do it. Muffling aids outside the studio is where moderation is the key. If you have multiple pieces of Gaff tape or MoonGel on a drum, you need to get some help from someone to teach you how to choose heads and/or tune.
Reso heads DO need to be changed. Some people assume a head change is only nessecary when a head brakes. WRONG. Even though Reso heads are not hit with sticks, they still get stretched every time you play and from thermal expansion and contraction. They also simply age. I personally like to change them once a year if your playing your kit a few hours a day 5 times a week. You could go a bit longer, but i would say 2-3 years tops. Another sure fire way to tell they are in need of replacement is if your re-tweaking heads alot more often even with new batter heads. Also if everytime you re-head your kit and re-tune it it gets more difficult. On a ported bass drum head, you could go alot longer. On snare reso heads on pretty heavily played kits, i normally due them every 6-8 months along with wires. On tour where failure is not an option and we are doing 5 or 6 two hour shows a week, Ill do reso heads every 6 months, snare reso's every 4 months and snare wires every 5 months. That is my normal pattern now. The exception of course is if the stuff fails earlier which happens when you do lots of outdoor gigs in the summer.
Any time you have a head off of a drum, go around each lug screw with a stubby screwdriver to make sure they are snug. Just be GENTLE. You don't want to actually further tighten them down each time or you will end up crushing the wood and any rubber washers involved. The whole purpose is to make sure nothing is loose. Unexplained buzing on toms and weird, sustained overtones are almost always either a bad head or a loose lug screw. I also shake each drum off the kit once the heads are on it to listen for anything rattling inside the lug casings. Lug screws do not need to be and should not be TIGHT. Just snug. Any good quality drum will have some sort of washer assembly designed to hold the screws tight without much force. Wood expands and contracts with tempature and humidity. If your lugs screws are too tight, you can crack the lacquer as well.
Avoid "The better mouse trap". Drum Dial's, Tension Watch, Torque Keys, etc will only end being a crutch for you. They are tools designed to help you repeat an already established tuning. The hard part IS the initial tuning. Think about it, once you have finall got your kit sounding good all on your own, now your going to give up on trying to master that very act on your own by using some gadget that looks like a great idea. There are far too many things that come into play that make such devices worthless. Head consistency, tempauture of the heads, tempature of the shells, what the tempature was when you first took your readings, etc. Hey, again, i am all about the work smarter not harder way of life, but i too thought those devices might help. I bought them all, they are all paperweights now. Nothing will replace feel and your ears. For the price of a drum dial you could re-head your kit twice. Two head changes will teach you more about drum tuning then one of those things.
Remember what works for some, will not for others. When at first you don't succeed, try, try again. Or, consult the Pearl forum.
http://www.pearldrummersforum.com/showthread.php?165089-SLIPKNOT1-Drum-Tuning
판매자연락처와 번호요청
판매자연락처는 상품등록시 본인인증연락처로 자동입력되며 개인정보보호와 매너거래를 위해 기본 비공개되며 구매자의 번호요청 댓글이 있을시 작성한 회원에게만 공개됩니다. ※제도정착을 위해 판매자님들의 협조 부탁드립니다.
댓글종류
일반/문의 댓글은 기존방식의 댓글로 자유롭게 이용하는 댓글이며
번호요청 댓글은 구매를 위해 판매자의 연락처를 알고 싶을때 작성하는 댓글입니다.
번호요청 댓글의 장점
-판매자의 개인연락처 무분별한 노출 방지
-비매너 구매자로부터 판매자 보호하는 안전장치
-댓글내역을 유지하여 판매자와 구매자 신뢰도향상
-서로의 플래닛방문하여 프로필에 거래후기를 남겨주시면 더욱 좋습니다
-댓글 작성후 댓글종류 변경 및 삭제 불가, 내용수정은 가능
-댓글은 판매자만 볼수 있으며 댓글쓴이 연락처 뒤 4자리 공개로 구매자 식별가능
-판매완료,판매취소시 번호요청 불가